RE: [diesel_mercedes] Re: Need headlight bezel (left side) for 1981 126 SD

 

On eBay, scroll on down:

http://www.ebay.com/sch/i.html?_from=R40&_trksid=p3984.m570.l1313.TR0.TRC0.H0.X1981+126+SD+tail+light&_nkw=1981+126+SD+tail+light&_sacat=0

 

Or try http://www.junkyarddog.com

…Bill in Oregon

From: diesel_mercedes@yahoogroups.com [mailto:diesel_mercedes@yahoogroups.com]
Sent: Thursday, November 20, 2014 6:55 PM
To: diesel_mercedes@yahoogroups.com
Subject: [diesel_mercedes] Re: Need headlight bezel (left side) for 1981 126 SD

 

Do you have rear tail light boards for right and left.  This is the plastic board that has the sockets for the tail light, brake light, and side light.  I want to make up a trailer light connector.  I want both connectors for both sides. 

Larry   1983 126 SD


 

__._,_.___
Posted by: <corvallis@peoplepc.com>
Reply via web post • Reply to sender • Reply to group • Start a New Topic • Messages in this topic (5)

.

__,_._,___
No comments:

[diesel_mercedes] Re: Need headlight bezel (left side) for 1981 126 SD

 

Do you have rear tail light boards for right and left.  This is the plastic board that has the sockets for the tail light, brake light, and side light.  I want to make up a trailer light connector.  I want both connectors for both sides. 

 

Larry

1983 126 SD


 

__._,_.___
Posted by: dittmer.larry@yahoo.com
Reply via web post • Reply to sender • Reply to group • Start a New Topic • Messages in this topic (4)

.

__,_._,___
No comments:

Re: [diesel_mercedes] Routine Lock Lubrication

 

Voltage reading. It finally warmed up to 30 degrees so I started my car to move it. Still hard starting. Anyway I checked the voltage. At super low idle it was 14V. At high revving it was still 14V. I turned the lights on and it dropped to 13.95V, did not matter if I revved or not. I did notice a tag on the alternator that said re-built but it was too dark to really see what it said. Its always worked good. Car is now parked until April. Max

On Thu, Oct 30, 2014 at 1:11 PM, vwnate1@yahoo.com [diesel_mercedes] <diesel_mercedes@yahoogroups.com> wrote:
[Attachment(s) from vwnate1@yahoo.com [diesel_mercedes] included below]



Prolly not =8-) .

I assume Max does .

At least they can go to any Jeep Dealer and get it .

Now I know why they changed the name on the can ! .

-Nate
      Bill  wrote :

Nate; being these are younger people, do they even know what a Heat R iser is?  Bill in Oregon

 


Subject: R e: [diesel_mercedes] R outine Lock Lubrication

Go to Chrysler / Jeep Dealer and ask the Parts Dept. guy for " Heat R iser Solvent " ~ it comes in a shaving cream can (remember those ?) with a plastic snorkel in the nozzle , what it is is graphite in a light carrying fluid that you shoot into the key holes and them work the key back and forth a few times , have a clean rag handy as you should spray it in the keyhole until it burps back out .

This same product will work wonders on every key lock you have , NOW is the time of year to do every lock on the property so they'll work easily and smoothly until spring .

DO NOT get suckered into using WD40 or other worthless crap in key locks ! it's a solvent that washed the dirt and lubricant out allowing temporary ease of operation as the lock's delicate innards rapidly grind them selves to death .

I have posted the MoPar P/N before .

-Nate

 




__._,_.___
Posted by: Max temple <jasperezra@gmail.com>
Reply via web post • Reply to sender • Reply to group • Start a New Topic • Messages in this topic (33)
Check out the automatic photo album with 1 photo(s) from this topic.
Morris.Oxford.jpeg

.

__,_._,___
No comments:
Subscribe to: Posts (Atom)