[diesel_mercedes] CV Joint Grease ?

 

I thought I'd asked this but don't see it so here goes....(? again ?)

I'm getting ready to clean, re pack and re boot a pair of German LOBRO annular CV drive axles and didn't see any CV specific grease at my F.L.A.P.S. .

So, what all do you guys use or recommend ? .

Brand and typ please, vendor info too if you know who carries it .

TIA,

-Nate
LIVE in the world as it is, WORK to make the world as it should be

__._,_.___
Posted by: Nate <vwnate1@yahoo.com>
Reply via web post • Reply to sender • Reply to group • Start a New Topic • Messages in this topic (1)

.

__,_._,___
No comments:

Re: [diesel_mercedes] Steel Plate Needed [1 Attachment]

 
[Attachment(s) from Carl included below]

I've got steel rectangular bar drops from my Adirondack Pavillion,    6" x 4+ x 1/4" thick.

Do you have a way to cut it?  Just one? It's free as is.  I'm not sure of the cost of shipping from NH.


On 10/4/2019 9:26 PM, Nate vwnate1@yahoo.com [diesel_mercedes] wrote:
 
I need a small  piece of 6" X 2-1/2" X 1/4" steel plate, I'm sure someone knows where to buy a small bit of plate like this...... ? .

I'm in L.A. and will travel to pick it up and pay for it .

TIA,

-Nate
LIVE in the world as it is, WORK to make the world as it should be

__._,_.___

Attachment(s) from Carl | View attachments on the web

1 of 1 Photo(s)

Posted by: Carl <diyernh@comcast.net>
Reply via web post • Reply to sender • Reply to group • Start a New Topic • Messages in this topic (3)
Check out the automatic photo album with 1 photo(s) from this topic.
steeldrops.jpg

.

__,_._,___
No comments:

Re: [diesel_mercedes] Steel Plate Needed

 

Nate,

Check with these guys. They've got an LA location.

I've been to their OC location, and they had lots of pre-cut steel:

https://www.industrialmetalsupply.com/

Another, in Oc: https://www.schorrmetals.com/

Rob

==

On 10/4/19 6:26 PM, Nate vwnate1@yahoo.com [diesel_mercedes] wrote:
I need a small  piece of 6" X 2-1/2" X 1/4" steel plate, I'm sure someone knows where to buy a small bit of plate like this...... ? .

I'm in L.A. and will travel to pick it up and pay for it .

TIA,

-Nate
LIVE in the world as it is, WORK to make the world as it should be

__._,_.___
Posted by: Aleph93 <aleph93@ca.rr.com>
Reply via web post • Reply to sender • Reply to group • Start a New Topic • Messages in this topic (2)

.

__,_._,___
No comments:

[diesel_mercedes] Steel Plate Needed

 

I need a small  piece of 6" X 2-1/2" X 1/4" steel plate, I'm sure someone knows where to buy a small bit of plate like this...... ? .

I'm in L.A. and will travel to pick it up and pay for it .

TIA,

-Nate
LIVE in the world as it is, WORK to make the world as it should be

__._,_.___
Posted by: Nate <vwnate1@yahoo.com>
Reply via web post • Reply to sender • Reply to group • Start a New Topic • Messages in this topic (1)

.

__,_._,___
No comments:

[diesel_mercedes] from Bill in Oregon

 

You might try searching the internet using google. This is one light read that might nudge something in the memory.

Keep on.  Bill

https://www.bellperformance.com/bell-performs-blog/how-to-reduce-black-smoke-in-diesel-engines

 

Are your tires wearing down (smaller diameter) so the fuel consumption is getting worse?

==============================================

From: diesel_mercedes@yahoogroups.com <diesel_mercedes@yahoogroups.com>
Sent: Thursday, October 3, 2019 7:08 PM
To: Yahoogroups <diesel_mercedes@yahoogroups.com>; Yahoogroups <126diesel@yahoogroups.com>
Subject: [diesel_mercedes] Fuel Economy Check '84 300CD Slushbox

 

 

A/C run almost constsntly, Bibor used, mixed City Highway driving, this after I installed the BOSCH rebuilt injection pump ~ the car runs great, still emits a little bit of gray/black smoke when I pull away from a dead stop .

 

low fuel lamp lit @ 389 miles .

 

410 miles, 19 gallons, I get 22 MPG, am I calculating it wrong ? .

 

I don't see how it can smoke less and get worse fuel economy .

 

-Nate

LIVE in the world as it is, WORK to make the world as it should be

__._,_.___
Posted by: <corvallis@peoplepc.com>
Reply via web post • Reply to sender • Reply to group • Start a New Topic • Messages in this topic (1)

.

__,_._,___
No comments:
Subscribe to: Posts (Atom)