Diesel RVs

They usually break out the brand but there seems to be some confusion as to the application of a specific caliper. I've used ATE and Bosch. Its probably good to use the same brand on each side. What I can't figure out is if there is a difference in the calipers and if so, why it isn't it spelled out. There must be some difference given the 2 different rotor diameters and the fact that I got a set that rubbed on the hub. It has to be said that there isn't much clearance in any case between the caliper and the rim.

On Thu, Sep 10, 2015 at 5:04 PM, vwnate1@yahoo.com [diesel_mercedes] <diesel_mercedes@yahoogroups.com> wrote:

Mostly this is due to multiple different suppliers but also the taxis could be ordered with the larger brakes .

If you look on RockAuto.com they'll usually break out the different brands , ATE , Girling , Bendix etc. .....

Most of them interchange , good thing you had what you needed to make it work .

-Nate
Alan wrote :

I was operating on the apparently mistaken impression that most 80-85 123 cars had identical front suspension and brake components. I ordered a set of front calipers for an '84 300D. When I got them they looked comparable to what was coming off, but after installation the calipers rubbed on the hub. When I talked to Cardone's technical support staff they said that they had only 1 pair of part numbers for all of the variations including the 240D. I confirmed this general practice with the listings on several other sites offering rebuilt calipers. Since the 240D's and some early 300D's use 278MM dia rotors and the later 300s use 284MM rotors this seemed strange. I had already successfully fitted 300SD calipers to the car on an emergency basis. Since I was reluctant to go through another lengthy and expensive caliper swap, not being sure of what I would get, I installed a set of 300SD 284 MM vented rotors and matching calipers that I had in stock. The interesting thing was that the wheel bearings were not interchangeable between the 300D and SD. Can anyone shed any light on this problem.
--
Al Boucher

Al Boucher

__._,_.___

Posted by: Alan Boucher <alsthe1@gmail.com>

Reply via web post

•

Reply to sender

•

Reply to group

•

Start a New Topic

•

Messages in this topic (3)

Visit Your Group

New Photos 4

• Privacy • Unsubscribe • Terms of Use

__,_._,___

Bosch What else?

On Thu, Sep 10, 2015 at 5:14 PM, vwnate1@yahoo.com [diesel_mercedes] <diesel_mercedes@yahoogroups.com> wrote:

So ;

What brand regulator did you use ? .

FWIW ; some years / models it's dead easy to change out , others like you mentioned you have to loosen it and move it into gain access .

-Nate
Alan wrote :

Relative to battery light showing on dash when the 560 was operating with the headlights on. After the change the voltage improved to 13+ and the light no longer showed with the headlights on.
---------- Forwarded message ----------
From: sasha boucher <sashaboucher33@...>
Date: Mon, Sep 7, 2015 at 2:09 PM
Subject: alternator
To: daddy cel <alsthe1@...>

so, I finally got time to change the voltage regulator because while it LOOKS LIKE you can change it without at least loosening the alternator, you definitely can't. or I couldn't anyway. thankfully, I was able to loosen it enough to get to the VR without taking the whole thing off.
up until this point, I was using the cigarette lighter thing to see where the battery was at. around 12 volts with the car idling, would go up to around 13.6 during acceleration/normal driving, but never above that. I sprayed some WD40 on it (because that worked nicely with mine) and got it to go up to 14 once, but definitely needed new regulator as you can see by the picture.
so now, I'm going to put it back together and hope we're good.

--
Al Boucher