Re: [diesel_mercedes] Fuel Milage Check '82 240D Auto AC Used

 

I use Chevron Textron or Seafoam to clean the injectors and fuel system. Works great.

On Mon, Aug 1, 2011 at 12:30 AM, Nate <vwnate1@yahoo.com> wrote:
 


I put some MMO & a bit of Startron into the last fillup because the fluel in the intake screen was darkish , I removed the intake screen for cleaning and it had no chunks in it .

251 miles , 28.6 MPG , $4.09 / gallon of branded Diesel Fuel .

The AC is sweet ~ nice and cool , dry as a bone inside during to - day's muggy outing . SWMBO complained it was too cold in there , B.S. sayeth I .

-Nate
.


__._,_.___
Recent Activity:
.

__,_._,___

Re: [diesel_mercedes] Quick fix for clogged windshield sprayers

 

PB Blaster works well on most stuck or rusted parts.  I would guess it did most of the work. 

On Fri, Jul 22, 2011 at 1:22 PM, n61cm <jim@tazwade.com> wrote:
 

OK found this technique today out of desperation. Windshield sprayers all clogged up. First a drop of PB Blaster shot into each nozzle, then one minute later, a shot of air from a computer air duster can. Worked like a charm. Did the PB Blaster actually do anything? I don't know, maybe the air did it all by itself. But they opened up fully and immediately.

Jim


__._,_.___
Recent Activity:
MARKETPLACE
A good Credit Score is 720, find yours & what impacts it at freecreditscore.com.
.

__,_._,___

Re: [diesel_mercedes] Re: cv boot repair

 

Blaise,

And there was another one nearby for a jury rig. (Caution - it wastes a lot of time in the video):

<http://www.youtube.com/watch?v=PIanZCLILIM&NR=1>

Bobby

On Mon, Aug 15, 2011 at 1:29 AM, Blaise Colasante <supervee03@yahoo.com> wrote:
 

Here's the link to the funnel used for cv boot replacement.
Blaise


From: Bobby Yates Emory <liberty1@gmail.com>Sent: Saturday, August 6, 2011 11:52 PM

Subject: Re: [diesel_mercedes] Re: cv boot repair

 
John,

Stumbling around on You Tube, I found a Limey innovation:

<http://www.youtube.com/watch?v=so9gMxzJH4k&NR=1>

Panda uses a plastic cone to allow the user to stretch the boot into place.  One user had trouble with the plastic cone.  Another user suggested using a transmission funnel instead of the plastic cone. And using motor oil as the lubricant.

If the MB boot is stretchy enough, we might have a solution.  If not, Panda sells on eBay.  Don't know if we can leap the necessary hurdles.

(Thinking out loud - if the MB boot is stretchy enough for the high dollar stretcher, it should be stretchy enough for the funnel.)

(Anyone know a good lubricant for rubber that is slipperier than motor oil?)

Bobby

On Sat, Aug 6, 2011 at 11:18 AM, john public <brad_macaboy1234@yahoo.com> wrote:
 
I think a mechanical boot expander could be readily fabricated, operating similar to the pneumatic one in the video...seems less than cost/time effective to replace the boot, tho.




--
Toward freedom,

Bobby Yates Emory





--
Toward freedom,

Bobby Yates Emory

__._,_.___
Recent Activity:
.

__,_._,___

Re: [diesel_mercedes] missing modules 86 300SDL

 

The 2 large relays in the fuse box control the wipers and I believ headlights.  Not sure what you mena by "to bare female sockets on the firewall"  Can you post a photo?

On Wed, Jul 20, 2011 at 9:54 PM, <newdlhead@aol.com> wrote:
 

so, the modules in the fuse box are missing, and there are to bare female sockets on the firewall. what do these go to and are they rudely expensive?


__._,_.___
Recent Activity:
.

__,_._,___

Re: [diesel_mercedes] Re: replacing fuel lines on the 300sdl

 

All of the fuel lines are accessible from under the car.  The fuel tank is in the trunk behind the rear seat and does not need to be removed.  I would recommend replacing the entire line from back to front, as splicing in rubber hoses always results in leak later on.  The lines can be purchased aftermarket, but the MB lines are an exact length.  It may require lowering the differential from the rear subframe to access the fuel line junctions.  You do not have to remove the rear end from the car.  The lines will cost about $20 per line.  The main reason top replace the entire line is most often the lines are rotten where they are fastened to the car, i.e. the rubber mounts where all lines are routed along the bottom of car.  I agree that doing one at a time is best, bending while you are routing the line.  It is best to start at back of car and work your way forward. 

On Wed, Jul 20, 2011 at 8:50 PM, <audiolaw@aol.com> wrote:
 

Duuudes: 
 
    The access through the package shelf is for the fuel gauge sender unit. 
 
    Fuel lines are from the bottom of the tank.  Think of all the talk here about opening up the big drain lug to clean the tank bottom strainer.  Look around the lower reaches of the tank on the front side. 
 
Tom
 
 
In a message dated 7/20/2011 5:42:54 P.M. Pacific Daylight Time, liberty1@gmail.com writes:
 

New,

Sorry, I misunderstood - yes, I was talking about injector overflow lines. 

I have no knowledge about the fuel lines on the later cars, but some MB have ways to get to the fuel lines - something like - remove the first aid kit and then a flap under it - then you can get to the fuel lines.

Bobby

On Mon, Jul 18, 2011 at 9:28 AM, griegiry <newdlhead@aol.com> wrote:
 

thanks bobby, i gather you are talking about the injector overflow lines? i believe this fellow means the tank to engine lines. and that she leaks under the trunk. but that he was told the tank is not bad. i gather i have to get to the top of the tank to disconnect the fuel line from the sender, or does she have a spout out her side? i vaguely remember an article where a tank was removed from an sd to facilitate a greasecar kit, does not look like a job for the faint of heart.


--- In diesel_mercedes@yahoogroups.com, Bobby Yates Emory <liberty1@...> wrote:
>
> New,
>
> What usually goes bad are the fuel return lines. There are five or so.
> When I replaced one, enough fuel return line to do all of them was less than
> $10 at a MB dealer. (Still pretty expensive for 2 1/2 feet or so of small
> tubing.)
>
> Doing it is no big deal - do one at a time - remove the old one - cut a
> matching one from the new tubing - install - repeat. There are no clamps to
> fiddle with - just slide the old tubing off and slide on the new tubing.
>
> Other people have advised not to substitute another type of tubing - get the
> real thing from MB.
>
> Bobby
>
>
> On Sun, Jul 17, 2011 at 10:25 PM, <newdlhead@...> wrote:
>
> > **
> >
> >
> > i may have found an sdl. owner was told it needs new fuel lines. i was
> > told she weeps from the rear(graphic!) is this a big project? she has been a
> > sittin' two years, he says ac works. .what's the drill, anyone care to
> > point me to a previous post to save breath?
> >
> >
> >
>
>
>
> --
> Toward freedom,
>
> Bobby Yates Emory
>




--
Toward freedom,

Bobby Yates Emory


__._,_.___
Recent Activity:
.

__,_._,___

Re: [diesel_mercedes] Re: '83 300D Suspension noise. with video. '83 300D Sus...

 

I believe you are referring to the camber bushings and yes it can be a bear to replace.  It is difficult to diagnose the problem, but I had a similar noise with a W126 car.  The noise sounded like a spring mount, but ended up being a bad lower control arm bushing.  It was easier to replace with used control arm vs. having press out / in new bushngs.  That cleared the problem, but a front end alignment was necessary to adjust the camber and caster adjustment.  Good luck if you haven't already fixed.  I have a sourced for used parts if needed.

On Tue, Jul 26, 2011 at 2:15 AM, Dean Chandler <deanstud@comcast.net> wrote:
 

Well, the sound was definitely coming from where the track rod connects
to the lower control arm. Of course, the car doesn't make the noise
anymore... I checked and the bolt isn't loose or anything, so I guess
I'll just see if it comes back...

--
-Dean E. Chandler
'86 SDL
'83 300D
-=KE7TWY=-
Cornelius, Oregon
deanstud@gmail.com


__._,_.___
Recent Activity:
.

__,_._,___

[diesel_mercedes] Re: Re : newbie valve adjustment

 

That stuff has been on my tractor for ever, no leaks. Max

--- In diesel_mercedes@yahoogroups.com, "Nate" <vwnate1@...> wrote:
>
>
> If one hose was rotted sufficiently to rip they're almost certainly _all_ rotten and ready to begin leaking & do you dirt .
>
> Diesel hose is *special* so far only the German car partshaus and NAPA has ever had the correct stuff ,Pep Boys etc. sell similar crap but it'll soften up , swell & begin leaking fuel profusely in a few weeks , usually when you're far from home & wearing a nice shirt or have SWMBO in the car .
>
> I always carry 1' of it in the map pocket .
>
> Interestingly , the NAPA hose doesn't *look* right (no woven outer cover) but it's been on the car for a couple years now and never leaked a drop nor got hard nor blubbery.....
>
> -Nate
> Rodger wrote:
> >
> > thank you Brian
> >
> > The valves are all adjusted.
> >
> > I have to replace a fuel return hose before starting the car. One was too short to allow the valve cover off and it ripped.
> >
> > Rodger
> >
>

__._,_.___
Recent Activity:
.

__,_._,___

Re: [diesel_mercedes] Re: cv boot repair

 

On 8/15/2011 1:21 AM, Blaise Colasante wrote:

 
Sometime ago I saw a you tube video of a guy using a section of a funnel to slip the boot onto the axle. I may have saved the link...have to look for it.
Blaise


From: john public <brad_macaboy1234@yahoo.com>
To: diesel_mercedes@yahoogroups.com
Sent: Saturday, August 6, 2011 11:18 AM
Subject: Re: [diesel_mercedes] Re: cv boot repair

 
I think a mechanical boot expander could be readily fabricated, operating similar to the pneumatic one in the video...seems less than cost/time effective to replace the boot, tho.



Blaise,

Perhaps something gynecological would work as well.  We'll finally ship those parts today.  It's been crazy around here.  We're prepping 2 houses for sale.

Al Boucher

__._,_.___
Recent Activity:
MARKETPLACE
A better credit score can save you thousands. See yours at freecreditscore.com.
.

__,_._,___